When to Get Professional Fire Alarm Servicing

Read Time:4 Minute, 22 Second
When to Get Professional Fire Alarm Servicing

The majority of businesses are aware that their fire alarm needs to be checked from time to time. However, it is not always clear whether an in-house check is sufficient or if a qualified engineer is required. Here are the key points at which servicing becomes non-negotiable.

The Annual Service Is Non-Negotiable

The annual fire alarm service for commercial premises is detailed within the British Standard for Fire Detection and Fire Alarm Systems, BS 5839. This standard requires a competent person to carry out a full inspection and service of your fire alarm system on an annual basis, in addition to your weekly and monthly testing.

Watch For Repeated Fault Signals

A single fault indicator on a panel is not uncommon. It can take several weeks for a detector to become contaminated, or for a connection to become loose. The occasional loss of a zone on a panel can occur for a variety of reasons and usually clears itself on the next test. However, if a system repeatedly flags up the same fault(s), fails to clear on a reset, or loses several zones at once, it’s likely to need immediate checking by a competent person before it fails when you need it most.

After Any Building Work Or Rewiring

Changes to your premises – such as structural modifications like knocking through walls and building partitions, changes to kitchen and stores, as well as modifications to cabling – could affect the coverage of your detectors. In addition, detectors and sounders that were once clear of false ceilings could become hidden from view. Any such changes would require a full servicing visit to check the amended coverage and check the cabling routes throughout the premises against the original design.

Following A Change Of Use

If you have recently changed the use of your building, you need to consider whether your fire risk assessment and your fire alarm system are still adequate. For example, a fire alarm installed in an open-plan office may not be sufficient to protect a building that has been converted into let rooms or a shop that has been converted into a restaurant. Many of the issues found during inspections of commercial premises in Bedfordshire are due to the fire alarm system not having been checked and serviced since the building was converted into sleeping accommodation.

After A False Alarm Or Real Activation

Each and every false alarm must be investigated. It may be due to contamination from dust, steam, insects etc. or faulty sensors within the detector. If a detector is continually activating false alarms then it is likely to be contaminated. It is also wise to check the fire alarm system after a small fire has occurred. Even though the fire may have been small, it is possible that the sensors, wiring etc. could have been affected by heat, smoke etc. or even by extinguishing agents. It is always best to check.

Taking On A New Or Older Building

A technician on a stepladder working on a ceiling-mounted fire alarm detector in an office corridor

New buildings and older buildings with fire alarm systems recently purchased can hide surprises in terms of compliance with current wiring regulations for fire alarm cable, obsolete parts and lack of previous maintenance. Check the previous service history and log book for any fire alarm system that you take over and treat initial servicing as a priority if no servicing history can be found.

Keep The Log Book Up To Date

The fire alarm system log book is another important document that needs to be kept by all commercial fire alarm systems. It should contain a full record of all tests of the system, any faults that have occurred and how they have been repaired. This is evidence that needed servicing has taken place and it is required by fire inspectors and insurance companies alike. It would be best to keep this log book near the panel that controls the fire alarm system and ensure that the person undertaking the weekly test also records the test in the log book.

Choosing A Competent Engineer

Not all electricians are able to carry out fire alarm servicing. The servicing engineer will need to be certified by a recognised body such as FIA (Fire Industry Association) or NSI (National Security Inspectorate) and will test all aspects of the fire alarm system including battery voltage, sounder level, detector sensitivity, the programming of the panel and test all zones of the system individually. Advice from Bedfordshire Fire and Rescue Service regarding the requirements for fire alarms in commercial premises is available on the web and details what is required for a fire alarm system to be compliant with local requirements. It is always wise to choose a certified engineer to come and carry out servicing on your fire alarm system. More on Fire Alarms Bedfordshire can be found at Fire Alarm Systems.

Servicing a fire alarm is not a case of waiting for the annual visit. A simple phone call to a competent engineer to come and give your fire alarm a check up could save a lot of hassle in the long run. It is so much cheaper to have your system checked out than to find out the hard way that it hasn’t been working when you really need it.

About Post Author

0 0
Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Reply

Your email address will not be published. Required fields are marked *